Disclaimer:

    The views, information, or opinions expressed in the Industry News RSS feed belong solely to the author and do not necessarily represent those of IDEX Health & Science and its employees.

    Flexible Waveguides Exhibit Low Light Loss for Biosensors, Wearables

    Article obtained from BioPhotonics RSS Feed.

    Tiny, flexible waveguides, made in a clear silicone commonly used for biomedical applications, were created by a research team at École Fédérale de Lausanne (EPFL). To create the waveguides, the team used multiphoton laser direct writing, a microfabrication method in which a light-sensitive chemical is polymerized with a focused laser to create finely detailed 3D structures.

    Researchers optimized a laser writing process to create extremely narrow waveguides in PDMS. The new waveguides could be used to transport light in a variety of sensors, lab-on-a-chip systems, and wearable devices. Courtesy of Ye Pu, École Fédérale de Lausanne.
    The optical waveguides were fabricated in polydimethylsiloxane (PDMS). Phenylacetylene was used as the photosensitive monomer. Phenylacetylene has a higher refractive index once polymerized, compared to traditional materials. The researchers surmised that the refractive index (RI) of the phenylacetylene would be markedly different from the RI of the surrounding PDMS. This would help ensure that the waveguides, although tiny, would be able to confine light efficiently.

    The researchers soaked the PDMS in phenylacetylene, then used an ultrafast laser to induce multiphoton absorption. Multiphoton laser direct writing produces finer structures than one-photon processes because the volume of polymerization at each writing spot is smaller. Multiphoton laser direct writing allowed the researchers to directly initiate phenylacetylene polymerization without a photoinitiator. The researchers caused any nonpolymerized phenylacetylene to evaporate by heating the PDMS.

    “By not using a photoinitiator, we simplified the fabrication process and also enhanced the compatibility of the final device with living tissue,” said researcher Ye Pu.

    Using its new approach, the team demonstrated flexible waveguides made in PDMS that were just 1.3 μm wide. For the 650- to 700-nm spectral band, the waveguides demonstrated a transmission loss of 0.03 dB/cm. A light-based signal can travel through the new waveguides for 10 cm or more before an unacceptable degradation of the signal occurs.

    Waveguides smaller than 1 μm could be possible if the setup was optimized, said the researchers, who are now working to improve the yield of the fabrication process by developing a control system that will help prevent material damage during laser writing. They also plan to create an array of narrow waveguides in PDMS that could be used to construct a flexible endoscope with a diameter of less than 1 mm.

    “Such a small, mechanically flexible endoscope would allow a number of hard-to-reach places in the body to be imaged for diagnosis in the clinic, or for monitoring in a minimally invasive surgery,” Pu said.

    “To the best of our knowledge, these are the smallest optical waveguides ever created in polydimethylsiloxane, or PDMS,” Pu said. “Our flexible waveguides could be integrated into microfluidic lab-on-a-chip systems to eliminate bulky external optics needed to perform blood tests, for example. They might also deliver light for wearable devices such as a shirt featuring a display.” The new, flexible waveguides could also serve as building blocks for photonic printed circuit boards that use high-speed optical signals to transmit data in computers and other electronic devices.

    The research was published in Optical Materials Express, a publication of OSA, The Optical Society (https://doi.org/10.1364/OME.9.000128). 

    READ MORE
    Dec, 20 2018 |

    IDEX Health & Science is the global authority in fluidics and optics, bringing to life advanced optofluidic technologies with our products, people, and engineering expertise. Intelligent solutions for life.