FAQs


Here we have provided comprehensive lists of commonly asked questions regarding our products, processes, and procedures. This information is designed to support your inquiries, but if you don’t find the answers you are looking for we encourage you to contact technical support for further assistance. Please use the sort buttons under the FAQs tab in the vertical navigation panel to navigate between questions and answers that are specific to Fluidics and Optics.

HPLC stands for High Performance Liquid Chromatography, a laboratory analysis technique for achieving analytical information about a sample’s components through a controlled separation process.

An isocratic method involves using one mobile phase composition throughout an analysis. This is often achieved by premixing a mobile phase in one solvent reservoir and using only that mixture for an assay. It may also be achieved through the use of a more sophisticated pumping apparatus that allows for precise proportioning from multiple solvent reservoirs. Finally, it may be performed through the use of two or more pumps operating in unison.

High-pressure mixing refers to a pumping system that involves multiple pumps. Here, each pump in the system delivers a specified amount of a solvent in the form of a solvent stream. All the solvent streams in a system then come together in a mixing apparatus before exiting as a unified solvent stream. It is referred to as high-pressure mixing because the solvent streams are mixed together after they leave the pump, thus being on the high-pressure side of the pump. This term usually applies to gradient methods, but may also apply to more sophisticated isocratic analyses.

Low-pressure mixing only occurs with sophisticated pumps that are capable of precise proportioning from multiple solvent reservoirs. Here, the pump uses special electronic valves to obtain solvent from multiple reservoirs. This valve performs its proportioning prior to solvent entering a liquid end, thus being on the low-pressure side. This term usually applies to gradient methods, but may also apply to more sophisticated isocratic analyses.

A sample is separated into its components due to a process termed differential migration. This migration is controlled by the degree of attraction each component has for the stationary phase compared to the mobile phase. Usually, the various components that make up a sample will exhibit varied degrees of attraction, and it is based on these varied levels of attraction that separation takes place.

Optimal separations can be achieved by making strength adjustments to the stationary and/or mobile phases and selecting the right chemistries for these two phases can enhance the differential migration of the sample components.

The stationary phase of an HPLC system generally refers to the column, where the separations actually take place. Technically speaking, the stationary phase refers to the chemical compounds, usually bonded to silica beads, inside the column, where they remain in a static position—thus, they are stationary.

The mobile phase refers to the solvent mixture being pumped through the column. Because it is moving on a continuous basis, it is referred to as mobile.

Mobile phase chemical properties are often different than stationary phase properties. The difference between the properties is used to dictate the type of separation that takes place; therefore, optimal sample component separation is achieved through the use of the appropriate stationary phase and mobile phase compositions.

HPLC systems can be as varied as the type of analyses that can be performed. However, the typical system can be broken down to some basic components which are easily identified in most systems. The best way to identify system components is to follow the flow path of the mobile phase from beginning to end, which usually correspondingly identifies components from left to right in the system. First, there is the MOBILE PHASE RESERVOIR, which houses the solvent mixture used during the analyses.

The second component is the PUMP, which offers back-pressure regulator controlled flow of the mobile phase through the rest of the system. In most instruments, the mobile phase is degassed prior to entering the pump to reduce dissolved oxygen and bubbles, which can negatively impact chromatography results. This is often done by flowing the solvent through a DEGASSER comprised of a gas permeable membrane and vacuum source. Incidentally, it is vitally important that a pump function very well in order to insure reproducibility in chromatographic data.

The third component is the INJECTION VALVE, used to introduce a set volume of sample into the solvent stream.

Fourth is the COLUMN, often referred to as the “heart” of the HPLC system. It is here that the actual separations occur; without the column, no usable data can be obtained.

Fifth in the system is the DETECTOR. This instrument is vital, as it generates an electronic signal that can be interpreted into a trace. Quantifiable data is obtained by thorough examination of this trace.

Sixth is the WASTE RESERVOIR. Here the mobile phase and analyzed samples collect after passing through the rest of the system.

Last in our basic breakdown of an HPLC system is a RECORDER. While solvent does not come in contact with or pass through this instrument, the recorder is responsible for translating the electronic signal being generated from the detector into a printed trace, referred to as a chromatogram. Using mathematical formulas, analytical information can be gleaned from this chromatogram.

Introduction of a sample into the flow path is properly done through the use of an injection valve. This valve allows for the introduction of a sample without interrupting pump flow. With the injection valve in the LOAD position, sample is pushed through the needle port and into the sample loop (a piece of tubing with a known volume). Once the sample has been loaded into the loop, the valve is rotated to the INJECT position. By doing this, the pump flow is diverted through the sample loop, pushing out the sample in the process. The pump flow continues carrying the sample out to the column, where the separation begins.

An injection valve serves two purposes. First, it allows the redirection of the pump flow away from the sample holding loop, giving you the opportunity to fill the loop with a predetermined amount of sample. Second, it once again allows the redirection of the pump flow through the sample loop, where the solvent stream carries the sample slug onto the head of the column to begin the separation process.

Assuming the noise along your baseline is not due to anything electronic within your detector, there are two things that can be done to help minimize this problem.

First, you can adequately degas your solvents. Following the flow path, the solvent stream moves quickly from a high-pressure environment within the column to a low-pressure environment on the effluent side of the column. Often, if solvents are not properly degassed, the gases being forced to remain dissolved in solution due to the high pressure inside and upstream from the column quickly outgas when the pressure changes. This outgassing is visible in the form of bubbles in the solvent stream line. These bubbles can pass into your flow cell, and once there they can cause excessive noise. Adequate degassing can help eliminate the problem of outgassing and thus help eliminate the chance of bubbles forming in the flow cell.

The second thing you can do to help eliminate this problem is to use a back pressure regulator on the effluent side of your flow cell, because one of the primary factors causing bubbles to form in the solvent stream is the drastic drop in pressure the solvent experiences. Using a back pressure regulator forces additional pressure along the flow path, thus helping to ensure that any gas dissolved in the mobile phase stays dissolved until it has passed through the detector flow cell.

Several things can replace stainless steel parts in biocompatible situations. If you are looking to continue using metal, then in some cases titanium is an acceptable alternative. However, titanium is brittle and very difficult to cut, and in the case of tubing, it is very expensive.

For other purposes, almost universally, PEEK is a fantastic alternative to stainless steel. PEEK, or polyetheretherketone, can be used in high-pressure situations like stainless steel, and it is compatible with most chemicals used in HPLC. PEEK tubing is less expensive than stainless steel, easier to cut and more flexible. PEEK fittings are appropriate to be used with most all instruments. PEEK fittings offer high-pressure holding capabilities, and typically only need to be tightened finger tight, minimizing the need for special tools.

The most important step in preserving the life of your column is to use clean solvents and samples. This can be done primarily through the use of filtration. Utilizing solvent filters, both in the reservoir and inline as well as sample filters, can help keep the particulate matter that may be present in these chemicals out of your column.

Another concern you must be careful to keep in mind is proper care of your column. Many times a buffer may be used as part of your mobile phase, and depending on the type of buffer you use, if it is allowed to sit stationary for a relatively long period of time, some of the buffer may precipitate out and plug your column. As a general rule, you are going to leave your column unused for more than 24 hours and you are using a buffer that might precipitate, take a few moments to wash your column free of the buffer. For most columns, it is best to store the column filled with an organic solvent, like methanol or acetonitrile. However, make sure these chemicals are compatible with the stationary phase inside your column, because if you use the chemicals that aren’t compatible with your stationary phase, your column can be functionally destroyed.

As a final note, one of the best ways to insure longer functional life from your column is to use a guard column. Guard columns often have similar chemical stationary phases as the analytical columns with which they are being used. Therefore, if something in the samples or in the mobile phase can cause damage to your analytical column, that something will interact with the stationary phase within the guard column first, hopefully saving any major damage to your analytical (and more expensive) column.

A guard column is almost always recommended for use in your system, especially when you have components in your sample that may harm your sensitive stationary phase. At times you may find that some components in your sample seem to permanently bond with your stationary phase, eventually decreasing the efficiency and usefulness of the column, forcing early replacement.

When using a guard column packed with a similar stationary phase to that of your primary analytical column, it is possible to significantly increase the life of your column.

The guard column is a relatively low-cost product, designed to selectively filter out those components that might cause damage to your primary column. By allowing the harmful components in your sample to interact with its stationary phase material, the guard column keeps those components from exerting their effects on your analytical column’s packing. However, keep in mind that because the harmful components of your samples are interacting with the guard column, it must be replaced from time to time. This can be monitored by keeping track of the back pressure exerted by your column system. When the back pressure increases significantly, that should serve as a good indicator that it is time to replace your guard column.

We carry analytical guard cartridge assemblies for just that purpose. Designed to be inexpensive and practical, this system is available packed with plain silica, packed with C8 or packed with C18 bonded phase. The different versions are color-coded for easy identification, and they are available in a variety of sizes to best match the size of column you are working with. Because of their short length, they will not significantly affect the chromatography provided by your analytical column.

The IDEX Health & Science Column Couplers are assembled using either our stainless steel or PEEK tubing in conjunction with Fingertight fittings. These universal couplers permit the lowest swept-volume connection of any coupler on the market, offering zero loss of column efficiency. These couplers will connect any column with 10-32 coned internal threads to a pre-column or guard column with the same threads.

We also have a single-piece coupler available. For more information, contact your local IDEX Health & Science Distributor or IDEX Health & Science directly.

Once a ferrule has been properly swaged onto a piece of tubing, Dimension X is defined as being the length of tubing extending past the tip of the ferrule. It is this length that often varies from one manufacturer to another, and is the source of interchangeability problems.

Dead volume is defined as that portion of the flow path which is not directly inline,that is, unswept. It is these small spaces within your system where remixing of the separated sample bands occur, or where the initial sample is diluted with mobile phase. Dead volume should be minimized in a system, especially when small-volume columns of high plate numbers are used. Many times, dead volume can manifest itself through poor analytical data, often seen as split peaks or broad peaks on your chromatogram.

It is important to note that “dead volume” does not typically refer to the overall internal volume of a product or system. Usually, at least some portion of the pathway through a product is directly in the flow path — this volume is typically referred to as “swept volume.” For proper reference to the total internal volume, the term “void volume” should be used.

A micron is defined as being one one-thousandth of a millimeter. For comparison, a standard human hair is approximately 150µm in diameter. The term micron is often used to define pore sizes of filters and other frits, as well as to define particle size of the packing material used to pack columns.

As a reference, the most typical flow rate used in HPLC is 1.00mL per minute. This is often an adequate flow to elute (complete the separation process of) sample components in a relatively short time. Please note that the flow can vary vastly from this amount, ranging down into the microliters per minute up to 100mL per minute or higher.

An inline check valve is a special valve that is placed in the flow path where you wish to limit fluid transfer to one direction. Ideal placement for this fitting is on the effluent side of the column to prevent post-column derivatization agents from flowing back up the column and poisoning the column if your HPLC pump were to shut down. Placement on the post-column reagent line may also be desirable to prevent mobile phase from contaminating the reagent if the auxiliary pump were to fail.

Pump check valves are mechanisms designed with a special seal internal to its structure, one that allows solvent flow to proceed in only one direction. They are usually placed on both sides of the pump head, such that when the piston draws back to fill the pump head with fresh solvent, it does not pull back on the already expelled solvent. And when it expels the solvent it has taken in, it does so only in the direction of the fluid path, not back into the solvent reservoir.

Some check valves use a dual ruby ball and sapphire seat combination internally. The first set is designed to provide the primary sealing surface inside the check valve, while the second combination is designed as a backup to the first, in the event the first one should fail. The use of this sealing technology incorporates the pressures generated by the pump and your system to force the ruby ball against the sapphire seat, creating the seal needed by your pump.

An inlet solvent filter is a specialized frit, designed to attach to the inlet lines of the pump. As the mobile phase passes through, particulate matter larger than the pores in the filter is held up in the filter’s meshwork and not passed through. This helps insure the mobile phase is clean and free of material that might cause damage to other system components downstream. Common pore sizes of inlet solvent filters are 2µm, 10µm, and 20µm.

An inline solvent filter can make a very useful and protective addition to your system. Placing it between the pump and the injector, an inline solvent filter can protect your injector and the rest of your system—including your column and flowcell—from most particulate matter that exists in your solvent stream.

Where does this particulate matter come from? One source is from your solvent itself. If you have not pre-filtered your solvents, or if you don’t use a solvent filter in your reservoir(s), there is a good chance that some particles are present. Another source of contaminants is the pump seals themselves. As your pump’s pistons move back and forth through the seals, the friction created can cause small particles of seal material to fleck off and enter the solvent stream.

When any of this particulate matter passes on to your injector valve, it may get held up within the small passageways built into the valve’s seal. Once this occurs, it can cause flow blockages which may result in poor or no sample being injected. It may also result in the blocking of the solvent stream, which would be evident in a high pressure build up. One of the worst scenarios that can occur, however, is that the contaminant lodges between the seal and the inner face of the valve itself. As the valve rotates back and forth on subsequent injections with this particulate matter between the seal and valve face, both the seal and the valve face can become scored permanently. A scoring on either of these surfaces can allow fluid—either the sample or the solvent stream—to begin flowing in places it should not, usually resulting in a leak of fluid from the valve itself.

If the contaminants should happen to pass through the injection valve and continue on along the flow path, they could possibly enter the column, where they can ultimately cause poor chromatography.

The ideal placement of an inline solvent filter is between the pump and the injector. This will protect your injector and the rest of your system, including your column and flow cell, from particulate matter that may exist in your solvent stream.

The UHMWPE polymer used to manufacture the A-426 filter is very hydrophobic, and if your solvents are aqueous, the filter actually resists contact with that liquid. To rectify this problem, it often proves useful to prime the filter with an organic polar solvent, like methanol or acetonitrile prior to using it in an aqueous solution. By prewetting the polymer surface, air pockets are minimized, thus decreasing the occurrence of bubbles along your inlet flow path.

Through the use of one of our patented IDEX Health & Science Bottom-of-the-Bottle solvent filters. One version of the filter utilizes a replaceable stainless steel filter cup and allows solvent to be drawn to within .125″ from the bottom of your solvent reservoir. Our other version is a uniquely designed biocompatible all-PEEK polymer filter that incorporates a side port for optional helium sparging. This version allows solvent to be drawn to within .08″ from the bottom of the solvent reservoir. Brand new to our Bottom-of-the-Bottle line of products are the UHMWPE versions of our filters.

IDEX Health & Science manufactures 6-port solvent selection valves that are designed to let you choose a source solvent reservoir from up to six available reservoirs. With a rugged design that operates in applications up to 1,000 psi with the solvent coming in contact with no metal components, these valves are an excellent choice for organizing your multiple-solvent reservoirs.

Sparging is the process of bubbling a virtually insoluble gas, such as helium or argon, through a solvent in an effort to displace the gases which have dissolved into solution. A gas such as helium has a very low solubility in most solvents used in HPLC. By trying to force an inert gas like helium into a solvent which doesn’t “want” the gas to be present, the gases (like oxygen and nitrogen) that are present are driven out. This leaves a solvent with virtually no gas dissolved in solution. Therefore, when the gradient mixing takes place, bubble formation is minimized, helping to ensure better chromatographic results.

Some gases, like oxygen, nitrogen and carbon dioxide, have a tendency to dissolve into solution at a much greater rate than do inert gases such as helium or argon. Even though they do have a higher solubility in most solvents, they often do not have equal solubility in all solvents.

What does this mean to visible quality performance of your equipment? If you are running an isocratic method, pulling your pre-mixed solvent from one reservoir only, then it probably doesn’t mean much in reduced performance. However, if you are running any method that pulls solvents from multiple reservoirs, it can result in the formation of bubbles in your solvent line.

One very helpful way to keep the amount of dissolved gas in your solvents very low is through sparging. The sparging process forces an inert — and virtually insoluble — gas into a solution, driving out dissolved gases from the solvent. This helps prevent the formation of bubbles in your flow stream, helping to produce better chromatographic results.

A precolumn filter should be used primarily if you have concerns about particulate matter in your samples. As this material passes along the solvent stream without the filter in place, it could plug up the frit at the head of your column or cause damage to the internal packing of your analytical column. The pre-column filter prevents particles larger than the pore size of the frit inside the filter body from passing through.

Biocompatible is a term applied to a fitting or tubing material that will not change the bioactivity of biological materials during the contact times common to HPLC analyses. Typically, any time biological samples are being analyzed (i.e. proteins, blood, etc.) it is best to use fittings and tubing that are termed “biocompatible.”

PEEK is an acronym, which stands for polyetheretherketone. PEEK is a hard, yet slightly flexible polymer that is used in the manufacturing of many fittings and tubing commonly used in the HPLC industry. It has excellent chemical resistance to organic and inorganic liquids; only concentrated sulfuric acid and concentrated nitric acid will chemically attack it. PEEK tubing is not recommended for use with methylene chloride, DMSO, or THF due to a physical swelling effect. However, these chemicals do not adversely affect fittings, unions, or tees. Because of its broad range chemical resistance and ability to hold high pressures, it is an ideal product for nuts, ferrules, unions, and tubing. Please Note: The maximum recommended operating temperature for PEEK fittings is 150°C, and for tubing it is 100°C.

In most cases, because of the proprietary process IDEX Health & Science uses in the extrusion of its tubing, color permanence is ensured and leaching does not occur. Thus, colored PEEK tubing from IDEX Health & Science can be used safely in most general HPLC applications. However, if you still prefer to use non-colored PEEK tubing, we do carry natural versions of its standard PEEK tubing. Please contact your local dealer or IDEX Health & Science directly for more information.

PEEK tubing is extremely flexible and can be easily cut to your desired lengths with a razor blade. This tubing can be used with stainless steel nuts and ferrules, flangeless fittings, or any IDEX Health & Science universal Fingertight fitting. PEEK tubing can also withstand very high temperatures, and has a recommended maximum use temperature of 100°C, above which the tubing will hold to lower pressures.

PEEK tubing, even though it is polymer-based, can withstand pressures up to 5,000 psi or higher in many cases (dependent on the ID of the tubing; larger IDs require a lower maximum pressure rating. The solvent being used can also effect pressure ratings). Another nice benefit of this tubing is its very smooth internal surface, which cannot be matched by any stainless steel tubing and which minimizes the turbulence created by laminar flow of the fluid.

Very few solvents have been shown to not be compatible with PEEK. Two common solvents are known to directly attack the material: concentrated sulfuric acid and concentrated nitric acid. Other less common solvents that attack PEEK polymer include: halogenated acids such as hydrofluoric acid; hydrobromic acid; hydroiodic acid (hydrochloric acid is approved for use in most applications); and pure halogenated gases. There are a few other chemicals that exhibit a physical swelling effect on PEEK tubing, namely methylene chloride, DMSO, and THF. However, these chemicals do not adversely affect PEEK fittings.

Because the list of adverse chemicals is so short, PEEK is an excellent alternative to most other materials available commercially today, including stainless steel and titanium, as well as other polymers.

Tefzel (ETFE), or ethylene-tetrafluoroethylene, is a soft fluoropolymer that is good for sealing surfaces. In addition, it can be molded and extruded into a variety of products. Tefzel is extremely resistant to chemical attack; however, some chlorinated chemicals will cause a physical swelling of Tefzel tubing.

Delrin, or acetal resin, is a polymer that has excellent chemical resistance to most organic solvents. This polymer’s high tensile strength also permits superior threads that are not susceptible to wear. Delrin is not suitable for use with acids, bases or oxidizing agents.

PFA tubing serves as an excellent replacement for PTFE Teflon, particularly where you are looking for similar physical properties—including lubricity—as those of PTFE, and where gas permeability, surface texture, and inertness are issues.

Additionally, a high-purity grade of PFA tubing is typically used when only the lowest level of polymer contaminants can be tolerated. This ultra-clean grade of PFA is often used in the medical industry. For some applications, where light sensitivity may be an issue, you may also be interested in our black-colored tubing.

There are two very common sizes of tubing you will find in HPLC. The most common size of tubing is 1/16″ outer diameter, or OD. You can usually find stainless steel and PEEK tubing of this size as part of your system. You might also find PFA or Tefzel® tubing of this size.

The other most common size of HPLC tubing is 1/8″ OD. Usually tubing of this size is used as solvent transfer tubing from the solvent reservoir to the inlet side of the pump. Most often, it is manufactured from Teflon.

There are other sizes of tubing you might find in an HPLC system, ranging from microbore tubing, with ODs that range from .004″ up to 1/16″, to larger 3/16″ OD tubing and even 1/4″ OD tubing.

Your best option when choosing tubing, keeping in mind its permeability to gases, is metal tubing, such as stainless steel or titanium. However, these are often not very convenient to use in places where you would be most concerned about gases permeating the tubing walls. Often, polymer tubing is the tubing of choice for flexibility and ease of cutting purposes. But which is least permeable to gases? For the best performance, PEEK tubing should be your option of choice, as its gas permeability is virtually undetectable. Most fluoropolymer tubing, including Tefzel and Teflon tubing, is highly gas permeable and should not typically be used where gas permeation may be detrimental.

In certain high-pressure applications where metal tubing is necessary but stainless steel cannot be used — such as those involving protein analysis — titanium tubing serves as an appropriate alternative. However, there are some disadvantages to using titanium tubing. It is brittle and care should be taken when bending it. Also, the use of acids can cause physical stress fracturing along the walls of the tubing.

For most applications where titanium is being used for biocompatibility purposes, PEEK polymer tubing is a viable option. PEEK tubing offers excellent solvent compatibility, is easier to use, and costs less then titanium tubing.

Pre-cut tubing available from IDEX Health & Science has square, burr-free, polished ends. Such high quality finishes are important in allowing you to make zero dead-volume connections. Maintaining the lowest dead volume possible is vital between the sample injection valve, the column and the detector. Tubing cut with commercially available tubing cutters or a standard file will result in rough, uneven ends. These imperfections provide ample opportunity for dead-volume chambers to form, reducing the overall chromatographic efficiency.

A frit is a porous metallic or polymeric material, usually formed into a disc shape. A frit is designed to prevent the passage of particulate matter while allowing fluid to flow through it. Two common uses of a frit is as an inline solvent filter and to contain the packing material inside a column tube. Frits vary in porosity from 0.5µm (used as inline filters for protecting an HPLC column) to 20µm (used for large particulate filtration in high-flow systems).

IDEX Health & Science is the only manufacturer of 100% PEEK frits, which are indeed biocompatible, inert, and offer uniform porosity for more reproducible frit-to-frit operation. They are available in 0.5µm, 2µm and 10µm versions.

A back pressure regulator is a device placed in the flow path after the detector to maintain a positive pressure on the effluent line leaving the column and the flowcell. Doing this helps minimize outgassing problems that often occur within the flowcell as the solvent in the flow path moves from the high-pressure environment of the column to the low-pressure environment (room pressure) after the column.

In addition, a back-pressure regulator can be used directly after a pump. In this configuration it will operate as a pump preload, and serve to help the pump operate more efficiently with less flow pulsation and/or disturbances.

In response to the need to have very little additional swept volume added to the flow path and still have the convenience of a back-pressure regulator, IDEX Health & Science has developed its Ultra-Low Volume Back-Pressure Regulator. With maximum internal volume of only 6 microliters, this product efficiently provides an even back pressure while minimizing band spreading; it’s hardly even noticeable in your system.

One of the primary causes of slowly increasing pump pressure is the buildup of material on a filter or frit surface, forcing the pump to work harder to achieve the same flow rate. This build up is usually caused by particulate contamination in the mobile phase, solid particles from the sample being introduced into the system, or breakdown particles from seal surfaces, primarily the pump seal. Another source of increased pressure can be the slow deposit of impurities or other sample components that permanently bond with the stationary phase within the column. As this deposit increases, it takes more effort from the pump to push the sample and mobile phase through in order to maintain the set flow rate. In order to solve this problem, it is best to go through your system and change – one at a time – the filters and frits, and maybe even the column, until the pressure goes back to normal. Keep in mind that if you make a change on your system and the changed part does not improve your system’s performance, it is usually safe to put the original part back in and save your new part for a future necessary use.

Typically in this situation, something has seriously and completely blocked the flow path, such that no matter what effort the pump goes to in order to push the necessary mobile phase through, it cannot be achieved. This can be in the form of a serious filter or frit blockage (often due to a precipitation effect of some sort), or it can be due to a large contaminant blocking the tubing through hole. Another source of this problem could be the outlet check valve malfunctioning, not allowing fluid to pass in the appropriate direction. The best way to solve that problem is to start at the furthest point along your flow path where the blockage could theoretically be, and begin disconnecting junctions along the path, all the while monitoring the pressure to see when it drops. As soon as you release a connection in front of the blockage, you should see an almost instantaneous release of pressure, as well as the return of fluid flow.

Two primary sources can cause this problem. The first problem is that something has suddenly caused a fairly major blockage in your system – either through contamination or precipitation – but the blockage is not so major that flow cannot get past, and thus the pump just works as hard as it needs to in order to achieve that flow. The other source of the problem is a defective pressure transducer or regulator, suggesting that the reading you are observing is not an actual reading, but an artificial one created by your pressure readout device.

The back pressure associated with your tubing is directly relational to the length of the tubing, the flow rate of the solvent moving through the tubing, the solvent viscosity, and the inner diameter of the tubing. In most cases, the back pressure is negligible for standard lengths and inner diameter sizes used in HPLC.

As a general rule, stainless steel fittings are interchangeable initially, prior to the ferrule of the fitting being swaged into place. However, also as a general rule, once a stainless steel fitting has been swaged into place on a piece of tubing, it is best to use only that fitting with the mating part into which it was initially swaged.

The reason stainless steel fittings are not interchangeable after they have been swaged into place is due to what we will term “Dimension X.” This “dimension” refers to the length of tubing extending past the ferrule of a fitting that allows the tubing to have a flush connection at the bottom of the union or adapter into which it is being tightened. Depending on the manufacturer, this dimension can be longer or shorter than others. Keeping this in mind, let’s look at a couple of scenarios that might help explain this a little more in depth.

First, assume you have swaged a stainless steel nut and ferrule into a manufacturer’s union where Dimension X is long. Now, you remove the fitting from this union and try to attach it to another manufacturer’s union, where the requirements for Dimension X are short. Now your tubing extends past the ferrule too far, and no matter how much you tighten the fitting, you will never be able to create a seal between the outer surface of the ferrule and the inside surface of the union

In the opposite scenario, you swage a fitting into a manufacturer’s union where Dimension X is short. You then try to move this to a union where the required Dimension X is long. You are able to get a tight seal with the fitting, but you have introduced a dead volume chamber between the end of the tubing and the bottom of the union. Depending on the location of the union, this dead volume space can lead to remixing of your sample components and extra turbulence, among other problems.

Once again, as a general rule with stainless steel fittings, always use the same mated fitting initially used to swage one of these fittings in place.

If you are in a situation where you need interchangability, we recommends Fingertight Fittings. With Fingertight Fittings the ferrule does not permanently swage.

Fingertight fittings comprise a special category of fittings designed to replace stainless steel fittings. The first Fingertight fitting was designed and introduced to the HPLC market in March, 1984.

There are several types of finger-tightenable fittings on the market now, and the fingertight fittings have become very popular. There are several reasons for their popularity:

First is the convenience of fingertight fittings. It is convenient to be able to disconnect tubing without getting out the wrenches. Second, fingertight fittings are universal and the fitting does not attach permanently to the tubing. You can use the fitting in one receiving port, disconnect the tubing and fitting, attach the tubing to another manufacturer’s port and use the same fitting.

Third, since you are using your fingers to tighten the fitting, there is less chance of over-tightening (a major cause of leaks and hardware damage with stainless steel fittings). Lastly, fingertight fittings use a polymer (plastic) ferrule. The polymer ferrule does not score or scratch the cone in the mating fitting, so your fittings last longer. This is one of the reasons you should use fingertight fittings on your column — column end fittings and other mating ports will last longer with fewer leaks.

The part of the Fingertight fitting that wears most quickly is the sealing surface. With a two-piece Fingertight fitting, the sealing surface is engineered into a replaceable ferrule. Thus, when the ferrule is worn, you simply replace the ferrule instead of the entire unit, making this type of Fingertight a more economical choice than the one-piece versions.

Usually, flat-bottom fittings come in either 1/4-28 or metric thread size. However, we also manufacture a line of special flangeless fittings, known as our VacuTight line, which allow a flat-bottom connection in a 10-32 port. We also offer an adapter that has 1/4-28 male flat-bottom threads and 10-32 male threads.

IDEX Health & Science developed the line of LiteTouch® ferrule systems, available in both 1/16″ and 1/8″ sizes. Each ferrule system consists of two parts: a double-coned ferrule and a stainless steel compression ring. This design accomplishes two important functions: First, because compression is occurring in two places, the ferrule system will hold to higher pressures. Second and most importantly, the stainless steel lock-ring serves as a bearing, preventing the tubing from twisting during the tightening of the fitting. This ferrule system can be used with specially designed PEEK polymer or stainless steel nuts.

Use of the Super Flangeless ferrule systems manufactured by IDEX Health & Science. Through the use of a lock ring around the back of the ferrule, the ferrule system works like a seal and a bearing, preventing the twisting of the tubing and thus virtually eliminating the loosening of the fittings that occurs in some applications that use the standard flangeless fittings.

Available with PEEK or Tefzel ferrules for 1/16″ OD tubing and 1/8″ OD tubing. Also available with a Kel-F ferrule for 1.8 mm OD tubing.

We manufacture a variety of stainless steel, PEEK or Tefzel tees, Y’s and crosses designed to perform this function.

These products are engineered with small thru-holes to minimize the internal swept volume. Available in standard 10-32, 1/4-28 and 5/16-24 threads, these parts allow the connection of your tubing with standard Fingertight or flangeless fittings.

IDEX Health & Science carries a line of fittings that use PEEK tubing sleeve to allow the connection of capillary tubing to mating ports, with standard 1/16″ threads (10-32 style). The tubing sleeves are standard 1/16″ OD and are available as part of our standard product line.

To use the system properly, first insert your capillary tubing into an appropriately sized PEEK tubing sleeve, ih the sleeve ID approximately .002″ greater than the OD of your capillary tubing. Then slide the nut and ferrule over the sleeve. We highly recommend the use of our F-140 stainless steel fittings with PEEK ferrules for the proper operation of these sleeves. Next, push the tubing sleeve assembly into your port until it bottoms out, and tighten the fitting finger tight.

Additionaly, IDEX Health & Science has added a line of special FEP Teflon tubing sleeves for this same purpose. Functionally, they perform just as our PEEK tubing sleeves do; however, due to the relative softness of the Teflon tubing sleeves, standard SealTight Fingertight fittings may be used.

In most cases, these assemblies will hold to 6,000 psi.

Additionally, we manufacture Minitight fittings designed to hold capillary tubing. One style is specifically for capillary tubing with a .020″ outer diameter without the use of a sleeve. Because these fittings have standard 10-32 threads to be used in standard 1/16″ tubing ports, if your capillary tubing is sized appropriately, these fittings provide a simple, easy-to-use alternative to connecting your capillary tubing to standard ports. Another style of the Minitight fitting is designed to be used with our MicroTight tubing sleeves. Please contact us for further information.

Through the use of the IDEX Health & Science’s new Conical Adapter, you can create a union between your standard HPLC tubing and your peristaltic tubing. With this new adapter, 1/16″ or 1/8″ OD rigid tubing is connected to a fitting that allows peristaltic tubing to slide easily on and off of.

If you prefer something that makes a tighter connection with peristaltic tubing, you might try our P-757 or P-767 Peristaltic Tubing Adapters. These are specifically designed to facilitate the connection between 1/16″ OD rigid tubing and peristaltic tubing ranging in inner diameter from 1.22mm to 3.05mm.

IDEX Health & Science has created the Precolumn MicroFilter, the Inline MicroFilter and the Mini MicroFilter specifically for this purpose. Most of our MicroFilters utilize our MicroTight tubing sleeves along with two Micro-Fingertight fittings to accommodate most sizes of capillary or fused silica tubing. Two versions of our mini MicroFilter directly connect 360-380µm OD capillary tubing without the use of tubing sleeves.

The Precolumn and Inline MicroFilters retain particles larger than 0.5µm flowing through capillary tubing, with the use of a built-in 0.5µm PEEK frit. Capable of holding 5,000 psi of continuous pressure, these filters can be used in either high-pressure or low-pressure environments. The Precolumn MicroFilter has 10-32 male threads and is designed for direct-connecting into your microbore or other column. The Inline MicroFilter utilizes 6-32 threads for use with our Micro Fingertight fittings.

The Mini MicroFilter contains a thin stainless steel microscreen that offers a dramatic reduction in theoretical void volume, at only .085 microliters (includes frit volume). This filter is available with 1- and 2-micron porosity replaceable filter capsules, and employs a combination of a female nut and a specifically designed ferrule.

IDEX Health & Science has developed a line of Quick Connect Luer Adapters, allowing the connection of standard HPLC tubing utilizing commonly found thread dimensions: 1/4-28, 10-32 or M6. Central to the function of the adapter is a luer-lock connection in the middle of the part, such that you can split apart the union in the middle through a simple twisting action without disturbing the HPLC tubing connections on either end of the adapter.

Also, through mixing and matching, you can easily create an assortment of adapters to which you can connect a variety of standard fittings. Additionally, IDEX Health & Science has introduced the innovative LuerTight™ fittings system. This unique connector family allows a quick disconnection between 1/16″ and 1/8″ OD tubing without the need for threaded nuts to hold the tubing into place.

The Quick Connect Luer Adapters are available in either ETFE (Tefzel) or PEEK polymers; the LuerTight fittings are manufactured primarily from polypropylene.

Pharmacia columns typically employ the use of a male, Metric (M6) threaded nut to make a connection into your system. There are a variety of adapters you can use that are engineered to adapt Metric threaded fittings to the two most common U.S. Customary System thread dimensions: 10-32 and 1/4-28. IDEX Health & Science manufactures an array of adapter styles, ranging from a union between two fittings (one metric and the other either 10-32 or 1/4-28) to a male-to-male style, which allows you to change one thread type to another.

You can use a special barbed adapter manufactured by IDEX Health & Science. These adapters have two male sides: one with a barb to fit snugly inside your soft peristaltic tubing, and the other end engineered to fit into any standard 1/4-28 flat-bottom port.

You can use a special barbed adapter manufactured by IDEX Health & Science. These adapters have two male sides: one with a barb to fit snugly inside your soft peristaltic tubing, and the other end engineered to fit into a 10-32 coned female port.

We offer some flangeless-type fittings that will work with your 3/16″ OD tubing. The flangeless nuts are manufactured from PEEK (part number P-132) and from Delrin, an acetal resin (part number P-138). For general organic or neutral pH applications, the Delrin version offers sufficient compatibility. For the best overall solvent resistance, however, the PEEK version is recommended. The ferrule you will need to use with the nut is part number P-133, specifically manufactured for use with both the P-132 and the P-138, and with 3/16″ OD tubing.

Our Universal Prime/Purge Valves are designed to connect inline: one along the 1/8″ OD flow path of most standard pumping systems and the other along the 1/16″ OD tubing flow path on the high-pressure side of the pump. These units are actuated through the use of a standard, luer-tipped syringe and allow you to pull air bubbles out of the solvent line easily and readily.

IDEX Health & Science has offers a high-pressure, biocompatible Semi-Prep Inline Filter. It consists of a stainless steel body, two PEEK end fittings and a replaceable PEEK frit. Once you buy the unit, the only part that will need replacing is the PEEK frit inside. Available with either 2µm or 10µm frits. The 2µm version has a pressure drop of approximately 40-45 psi at a flow rate of 100 mL/min of water across the frit. The 10µm version has a pressure drop of less then 10 psi under the same conditions.

Please Note: our Semi-Prep Inline Filters are engineered to be used with 1/16″ OD tubing utilizing polymer fittings, such as our one-piece F-120 Fingertight fitting.

We have our Flangeless Nut Extender Tool that is especially useful to tighten or loosen IDEX Health & Science flangeless nuts in hard-to-reach places. The tool’s design and plastic construction prevent over tightening, eliminating the potential problem of breaking off the heads of nuts. In addition, this product provides relatively uniform tightening of flangeless nuts into unions, tees, crosses and valves, taking the guess work out of the tightening process.

The extender tool can be used to tighten flangeless nuts on tubing with an outer diameter equal to or less than 1/8″.

To help tighten our Headless Flangeless Nuts, IDEX Health & Science has developed a special Extender Tool, the P-297. This aluminum tool lets you easily tighten Headless nuts, thus improving their holding power.

The colored ring around the IDEX Health & Science frits actually do signify a micron size. Following is our color-coding:

  • Red = Titanium 0.2µm
  • Blue = 0.5µm
  • Green = 2µm
  • Tan = 2µm
  • Black = 0.5µm
  • Yellow = Titanium, 2µm
  • Clear = 5, 10 or 20µm

We manufacture an assortment of nuts that utilize the M6 threads, which are standard for Pharmacia systems. The P-207, P-207S, P-226 and P-288 are manufactured to be used with 1/16″ OD tubing and can be used our 1/16″ flangeless ferrules.

The P-307, P-307S and P-326 are designed for use with 1/8″ OD tubing. These nuts are compatible for use with any 1/8″ flangeless ferrule available from IDEX Health & Science.

Please note, you can identify the metric flangeless nuts manufactured from IDEX Health & Science by a small mark (M6) molded directly onto a step on these nuts.

You can achieve this by using one of our Bulkhead Unions. We currently manufacture three different versions of this special union; the P-440, which has 10-32 internal threads; the P-441, which has 1/4-28 flat-bottom internal threads; and the P-442, which has metric (M6) internal threads. In addition, we also manufacturer three different stainless steel bulkhead unions, each with 10-32 internal threads, but with different thru-holes.

IDEX Health & Science manufactures polymer crosses out of PEEK and ETFE (Tefzel) which are engineered to be used with 1/4-28 flangeless fittings.

The P-634 and P-722 have a .020″ thru-hole, and are shipped with fittings designed for use with 1/16″ OD tubing.

The P-635 and P-723 have a .050″ thru-hole, and are shipped with fittings designed for use with 1/8″ OD tubing.

We manufacture several PEEK nuts with 5/16-24 threads that are designed to be used with 1/16″ OD tubing, 1/8″ OD tubing and even 3/16″ OD tubing. We also manufacture a Delrin (acetal resin) nut for use with 3/16″ OD tubing.

Most of these nuts are designed for flat-bottomed female ports. If you need a version to use with 1/8″ OD tubing and the female port is coned, then the P-131 nut with the LT-200 LiteTouch ferrule system should be used.

We manufacture a unique MicroSplitter Valve, which has been shown to maintain a controlled flow rate of as low as 2.0 microliter-per minute (with a 1mL/min. inlet flow). The split flow is adjusted by simply turning the thumbscrew on the valve to decrease or increase the amount of fluid leaving the valve from either port. If you wish to directly couple capillary tubing to the split port of the valve, use either our low-pressure P-452 or one of our high-pressure valves, M-405S and M-405T (an appropriate MicroTight tubing sleeve will need to be used with the capillary tubing). If you need more exacting capabilities, including a way to return to a previous setting easily, try our P-470 or M-472 Graduated MicroSplitter valves.

IDEX Health & Science offers pre-assembled low-pressure filters, with versions for 1/16″ and 1/8″ OD tubing. Using a frit held between flangeless fittings, these units effectively filter particulate matter from your mobile phase traveling through Teflon or Tefzel tubing.

Alternatively, you can filter at any point in your system where 1/16″ or 1/8″ OD tubing is connected to a flat-bottom 1/4-28, M6 or 5/16-24 port, using our innovative Frit-In-A-Ferrule™ products. These products seal and filter simultaneously through the incorporation of a frit into the body of a ferrule. The Frit-In-A-Ferrule is available in standard Flangeless and Super Flangeless ferrule styles with the choice of a PEEK or stainless steel built-in frit.

Use the IDEX Health & Science Pressure Relief Valve. By setting the internal cartridge to crack open at a pressure below the maximum pressure to which your syringe can be exposed, you allow a diversion of the flow to a waste container at any time the pressure on the flow path exceeds a safe operating pressure.

As experts in plastics machining, we’ll be pleased to answer your questions or help you understand the unique issues related to plastic machining, finishing, stress relieving, materials, assembly or other processing methods.

Your application, product development, and marketing requirements will determine the best plastic manufacturing method. There are twelve main considerations when determining whether to machine or mold your part.

  • Low volume requirements are most cost-effectively machined.
  • Closer tolerances are possible with machined parts.
  • There is more design flexibility when parts are machined.
  • Faster delivery is often possible when parts are machined.
  • Some parts are impractical or impossible to mold due to undercuts, heavy walls, long straight holes, etc.
  • Machining leaves no gate scars.
  • Machined parts have lower residual stress.
  • Machined parts have consistent properties.
  • Machined parts require no draft angles.
  • Machined parts have no weld lines.
  • Molded parts develop “skin” effects.
  • Molded parts may be less expensive to produce in greater volumes.

IDEX Health & Science performs adhesive, diffusion (thermal), solvent, and ultrasonic bonding and welding.

Your application requirements, environment, materials, and bond strength demands will guide us in determining the best bonding method.

We can use a variety of bonding methods in your application such as adhesives, solvents, thermal methods, and ultrasonic welding. We may also advise that simple mechanical fasteners be used in place of gluing.

Through correct tool geometry, machine feeds and speeds, and annealing.

IDEX Health & Science spends a considerable amount of time developing tools, fixtures and machining methods that create the least amount of thermal and mechanical stresses. And finally, we have twelve programmable annealing ovens that we use for intermediate and final stress relieving.

Many part failures that we see from other machining houses stem from improper or non-existent material stress management.

IDEX Health & Science utilizes vapor/chemical, flame, and mechanical methods to achieve desired surface finishes. We also use a variety of polishing/finishing methods to achieve the aesthetic and/or functional requirements for your part.

Usually, we’ll make every effort to get the best finish using our CNC machines. When surface finishes or optical/aesthetic requirements demand better than what our machines can provide, then we implement vapor and chemical polishing, flame polishing, or mechanical buffing. The method used is determined by the material type and the desired outcome.

It is important to note that we perform these operations on parts that we have manufactured, not on parts manufactured by others. That’s because control of residual stress, machining methods, etc. are critical to the success of any polishing method. If we have not manufactured the parts, we will not be confident that they have been manufactured correctly and can successfully be polished.

As a general rule, IDEX Health & Science can machine 0.006″ drilled holes with 50:1 aspect ratios, 0.010″ wide milled tracks, and hold tolerances down to ± 0.0002″.

Material type, part features, wall thicknesses, and other factors influence the low limits of machining possibilities. For some parts we can even achieve ± 0.000020″ tolerances

In some applications, we can achieve 100:1 aspect ratios in drilled holes.

The best way to determine the smallest features that we can machine is to let us analyze your drawings and application requirements. We will then give you an educated answer as to what we can achieve for you.

Most thermoplastics including acrylic, PVC, Ultem® polyetherimide, polycarbonate.

Diffusion bonding is a thermal process that fuses layers of material together, forming a permanent bond. Depending on your application requirements, IDEX Health & Science can bond many clear and colored materials like acrylic, clear PVC, GE Plastics’ Ultem® polyetherimide, ABS and polycarbonate. We may be currently bonding material you are using or may have diffusion bonded prototypes on hand (or in stock).

IDEX Health & Science also employs other bonding methods that may be more appropriate for your application, like adhesive bonding, solvent bonding, and ultrasonic welding.

Screw thread inserts may be a life-long source of stress in your part.

Screw thread inserts (STI) can cause continual radial stress in plastic because of the nature of how they are held in the material, but STIs can still be used in many applications. We recommend that ultrasonically installed inserts be considered as an alternative. The part will need to be annealed.

IDEX Health & Science would need to make a recommendation whether or not to use STIs after reviewing your application and material.

We offers most rotor seals in three standard materials: Vespel®, Tefzel®, and PEEK.

What are the pH ranges of the Vespel, Tefzel, and PEEK rotor seals?

The pH ranges are as follows:

  • Vespel 0-10
  • Tefzel 0-14
  • PEEK 0-14

The most important issue with these materials is whether the solvents, chemicals, pH, and temperature you are using are compatible with the rotor seal in your valve. For example, Vespel has a pH limitation of 10; Tefzel has a temperature limitation of 50°C. Chemical compatibility is addressed in the Materials and Tools section. In general, the different types of rotor seals will have the same lifetime and wear at about the same rate. Tefzel and PEEK rotor seals will require a slightly higher torque to turn the valve.

There is not a simple answer for this question. We have compatibility information on many common solvents; however, since there are thousands of chemicals in use, we do not have information for everyone.

Most likely a corroded thrust bearing is causing the noise. The bearing is located on the valve shaft and is normally well lubricated. If the valve has been mounted with the stator facing up, solvents leaking onto the valve could have leaked down the stator screws and into the thrust bearing. The thrust bearing can be easily replaced.

The valves we make for manufacturers (OEMs) are nonstandard products and are manufactured to OEM specifications. As a consequence, these parts are available only through the OEM. Inquiries should be directed to the customer service department of the manufacturer.

If the needle seal located in the rotor seal is not sealing around the needle, some of the sample will come out of the injection port. The outer diameter and length of the needle must be the correct size for the valve in order for the needle seal to function. If the OD and needle length are correct, the needle seal may have expanded through frequent use. The needle seal can be reformed by pushing down on the needle guide, which in turn pushes on the seal and closes it up.

Note: Never use a beveled, pointed, or tapered needle. This can permanently damage the rotor seal and stator face assembly.

If your valve is leaking out the injection port, vent line(s), or the stator ring and stator interface, most likely the rotor seal has been scratched. When replacing the rotor seal, I always check the stator face assembly to make sure that it is not damaged. Any chip or crack on the ceramic stator face will damage a new rotor seal in just one turn. If the pressure setting of the valve has been exceeded, this can cause the valve to leak as well.

First, confirm that the processor will operate separately from your instrument. To isolate the processor, disconnect the interface cable from your instrument, leave the power supply connected to the processor, and put the processor in the LOCAL mode. Verify the communications mode of your fluid processor module.

To check the communications in the level logic mode (LabPro part number ending in -01):

  1. Connect the black and red wires together. In a 2-position processor that is in position 1, the processor will switch to position 2; if the processor is in position 2, it will switch to position 1.
  2. Disconnecting the black and red wires will switch the processor again.

To check the communications in the BCD mode (LabPRO part number ending in -03):

  1. Connect the blue, green, yellow, and black wires. The processor should go to position 1.
  2. Connect the blue, green, red, and black wires. The processor should go to position 2.

If the processor is responding as described, the problem is with the instrument’s communication to the fluidic processor. Contact your instrument manufacturer’s technical service department.

Any instrument can be used to control a fluidic processor as long as it has external switches that are a contact closure or a TTL switch. Regarding the external switches:

  1. The switches must not send a voltage or a current to the fluidic processor or it will be damaged.
  2. BCD control requires four external switches.
  3. Determine whether the instrument’s output is level or a pulse logic.
  4. Both level and pulse logic require only one switch.

The change in color in the outer ring of the stator face assembly is due to a change in material. This material does not contact the fluid flow path, and the change will not affect the function of this part.

Standard Fingertight fittings will not typically work. UHPLC applications generally require fittings that have been engineered for very high-pressure environments.

Generally speaking, because of the very high system pressures present in most UHPLC applications, standard Fingertight fittings will not typically work. Making good connections in UHPLC applications will usually require either traditional stainless steel fittings or specialized fittings that have been engineered to work in the very high pressure environment of UHPLC.

– John Batts,
All About Fittings Guide

Download the All About Fittings Guide to learn more (must be logged in to download).

FAQs


Here we have provided comprehensive lists of commonly asked questions regarding our products, processes, and procedures. This information is designed to support your inquiries, but if you don’t find the answers you are looking for we encourage you to contact technical support for further assistance. Please use the sort buttons under the FAQs tab in the vertical navigation panel to navigate between questions and answers that are specific to Fluidics and Optics.

Increase the f-number (decrease the aperture size). This may require increased lighting. However, very large f-numbers (>f/22 image side working f-number) will significantly degrade the lens resolution.

The cost of manufacturing optics is extremely volume dependent. Mass-produced lenses provide excellent performance at low cost. Lenses produced in small quantity can cost five to twenty times more. It is always worth attempting to use or adapt a mass-produced lens for an application before designing a custom lens.

  • Continuous Wave
    Laser power is fixed or variable, but not delivered in a discrete pulse envelope.
  • Pulsed
    Laser energy is delivered in a single discrete pulse at a specified repetition rate.
  • Power
    The average power of a continuous wave (cw) laser beam expressed in watts (W).
  • Energy per Pulse
    The energy of an individual pulse expressed in joules (J).
  • Pulse Repetition Rate
    The rate at which pulses are repeated in a uniformly pulsed train of pulses expressed at the frequency of repetition of the pulses in the unit of hertz (pulses per second, Hz).
  • Gaussian Criteria
    The definition as used in the ANSI Z136.1 Standard for both beam diameter and beam divergence, require that these quantities be measured at the 1/e power point (63.2%) on the ideal Gaussian beam intensity profile. Note that most laser equipment manufacturers specify these beam properties at the 1/e2 power point (86.5%), which is a factor of 1.414 larger than the 1/e power point.
  • Beam Dimension
    Beam size (typically diameter) in millimeters, measured on the longest dimension.
  • Beam Divergence
    Change in beam size with respect to distance measured in milliradians.

Yes it is. In our previous catalogs, we sold the laser heads and the power supplies separately, whereas in our new catalog we have grouped them together to be sold as systems. We found that most people ordered both the laser head and its appropriate power supply on the same orders, so we decided to sell them as a system to make it easier on the consumer.

The 05-LHP-151 is the part number for just the laser head while the new system part number 25-LHP-151-249 designates the same laser head with its corresponding US power supply.

We understand that our customers may only need to buy just the laser head or just the power supply, so we still sell them individually.

Commonly, we can still supply a laser head or power supply, but just haven’t listed it in the catalog or on the website. This particularly applies to our older components. Most of the time these are still available and can be purchased by calling us directly.

Simply contact the Melles Griot’s Applications Engineering department to find the appropriate parts: Customer Support.

Helium Neon lasers can range from 800 MHz to 1575 MHz full-width-at-half-maximum (FWHM) depending on the design. The typical 632.8nm HeNe is 1400 MHz. The width of a single mode located under the gain curve is typically 1 MHz.

While re-gassing can provide some extension of the output performance in some gas lasers like the CO2, Argon and the higher powered side arm HeNes (which have external optics), it is not recommended or provided for smaller internal mirror coaxial tubes. Typical end-of-life failure for a HeNe is cathode sputtering. This occurs when the protective oxide layer on the cathode is expended through continuous bombardment by the laser discharge. There is no cost effective way of regenerating this layer. When the oxide layer is expended, the discharge itself vaporizes the “raw” aluminum and deposits this material, in its vapor state, on other surfaces such as the optics and the glass bore.

Most of our HeNe laser heads are CDRH / CE certified. Certified product for CDRH falls under one of the following classifications: Class II (<1.0mW), ClassIIIa(<5.0mW) or Class IIIb(<575mw). For CE our lasers are certified as a class 2 or 3B. Plasma tubes including some laser heads are not certified. In this case, it is the responsibility of the end-user to certify their system by meeting agency approvals. If CDRH / CE certification is a requirement for your system, be sure to verify the laser you select meets your needs.

All Melles Griot HeNe lasers have a recommended Laboratory or Module power supply (AC and DC input versions available), typically listed on the laser’s specifications sheet. If you are unsure which one is appropriate, please call us at 1-800-835-2626 and ask for a Laser Applications Engineer.

Rule of thumb in choosing a power supply: If you know the operating voltage and current of your laser, the power supply must have a voltage range large enough to fit the operating voltage for the laser and must be set at the appropriate operating current.

Coherence length is defined as the length over which energy in two separate waves remains constant. With respect to the laser, it is the greatest distance between two arms of an interferometric system for which sufficient interferometric effects can be obtained:

L = C / V

Where L is the Coherence Length, C is the speed of light and ν is the laser’s spectral line width

Coherence length will vary from laser to laser as a function of the Doppler broadened gain width; however, for a HeNe 20 – 30 cm is typical.

Optical mounts for on-line applications should be rigid, have positive locks, and have no more than the required adjustments. Laboratory mounting fixtures are generally not rugged enough for permanent on-line installations.

Machine vision optics should be mounted firmly but should not be stressed by excessive force. Do not rely on the camera C-mount thread to support heavy lenses. Either mount the lens and let the camera be supported by the lens, or provide support for both. Avoid over-tightening lens mounting clamps.

No. The image from a telecentric lens remains in focus over the same depth of field as that of a conventional lens working at the same f-number. Telecentric lenses provide constant magnification at any object distance. Therefore, they make accurate dimensional measurements over a larger range of object distances than a conventional lens.

In optics, “distortion” is the name of a specific aberration inherent in lens designs. Telecentric lenses offered by Melles Griot have low distortion. However, low distortion and telecentricity are separate, unrelated lens parameters.

No. By definition, a telecentric lens has a fixed magnification. Melles Griot offers a variety of telecentric lenses with large selection of magnifications.

Because the first element of a telecentric lens must be larger than its field of view, telecentric lenses are generally restricted to fields of less than six inches. Larger fields of view are possible in some applications, including web inspection, using line-scan cameras.

The recommended cleaning methods are dependent on the type of optic and its coatings.

You can download the recommended Melles Griot cleaning procedures document Cleaning Methods (PDF). The first part of the document describes five separate cleaning procedures with step-by-step instructions. The second part of the document lists which procedures should be used for which component.

You can also download this article Cleaning Optics (PDF) which explains the importance of the cleaning process to improve both the lifetime and performance of optics. Proper materials, techniques and handling procedures should be used to minimize the risk of damage.

Yes, the auto alignment piezoactuator controller has the ability to accommodate movements between a device and fiber during a pig tailing operation. However, when attaching fibers, two options are available, depending on the response of the throughput signal to the bonding process itself.

  1. Remain in TRACK mode — The auto alignment piezoactuator controller follows any relative movements by constantly and automatically optimizing throughput power.
  2. Switch to LATCH mode — this freezes the vertical and horizontal positions at optimum coupling.

The power connector/cord we use is a Mouser Electronics #172-4201 (mouser.com / tel. 800-346-6873). Ref. Shutter Pwr Cable – Mouser 172-4201.pdf

The recommended power supply is 12VDC, regulated, 3 Amp (providing some “reserve” over the 2.5A max load).

For direct TTL control of shutter “ON” time, DIP switches DS-1 & DS-2 should be ON. DS-3 should be OFF. On-board timer pot R3 should be set to it’s minimum value (full CCW). Maintain the TTL pulse as long as required to get desired shutter timing.

For on-board control of shutter “ON” time, all DIP switches should be ON. Initiate the shutter drive with a short TTL pulse (i.e., 20mS). Set on-board timer pots as needed to get desired shutter timing.

Notes – The shutter will not actuate if DS-2 and DS-3 are both OFF. See Operating Instructions sheet #25164B for more complete information.

For standard (black-painted metal) shutter blades, the transmission is essentially zero.

Maximum allowable light level will depend on many factors (wavelength, duration, blade material, blade coating, and environmental conditions), generally limited by coating damage and/or warping of shutter blades. Although we do not rate shutters for specific light levels, we can provide sample blades for application-specific testing by customers.

Contact a Melles Griot Applications Engineer for sample blade arrangements.

When the shutter blades are fully open (or fully closed for a normally open shutter); a dry contact is made with the X-synchronization, which provides electrical continuity.

We recommend only using the recommended 4X voltage pulse for 20mS; Using any lesser voltage will result in less reliable shutter actuation.

Shutters operated outside these conditions may function reliably.

Specifications:

Operational
Maximum Repetition: 2 Hz
Minimum Recharge Time: 200 msec (from de-energized to next actuation)
Duty Factor: < 100% (NOTE 1) Service life: >100,000 actuations

Environmental
Operating Temperature: -10C to + 40C
Humidity: Non-condensing
Shock/Vibration Resistance: To be verified by user, within system

We do not have a documented laser damage threshold for our Spring-Steel Blades with a Teflon-impregnated black matte finish. If this is a concern for your application Melles Griot will send you a shutter blade for testing.

Visit the Semrock FAQ page for more answers.

IDEX Health & Science is the global authority in fluidics and optics, bringing to life advanced optofluidic technologies with our products, people, and engineering expertise. Intelligent solutions for life.